High speed plasma machine, gas and combination CNC cutting marks the Start of 2M.
Machine plasma, gas and combination CNC cutting marks the start of the 2M is designed for plasma cutting of ferrous, non-ferrous, alloy metals and their waste, can cut parts shaped from metal with a thickness of 0.5 to 40 mm. or more. The speed of plasma cutting – up to 10 meters per minute.
High speed plasma machine, gas and combination CNC cutting marks the start of the 2M is designed for plasma cutting of ferrous, non-ferrous, alloy metals and their waste. Can work in two modes: automatic and manual.
The automatic mode provided by the computer numerical control (CNC) and is used for cutting shaped parts of any complexity within the dimensions of the desktop. Manual mode plasma cutting machine is designed for fast cut metal without the use of the program code.
The machine has several versions: Start-2M (basic version, without a cutting torch), Start Business (lighter version of the machine Start-2M, no cutting torch), the machine is thermal cutting with two torches (on the basis of the Start-2M), Start-BS (on the basis of machine Start-2M without a desktop, no cutting torch), start-a (machine plasma cutting on rack drive), Start-2m(Gas) (gas cutting machine, without a plasma cutter).
Cutting metal thickness up to 40 mm. produced plasma cutting, over 40 mm up to 100 and 200 mm. gas cutting.
– ability to cut parts shaped from metal with thickness from 0,5 to 40 mm
– significant increase in productivity and short payback period,
– combine on a single machine , plasma and gas cutters greatly increases the versatility of the equipment thermal cutting
– quality gas cutting (in the case of Felder, a gas torch) on the CNC machine above the quality of manual gas cutting
– low demands on maintenance, high reliability,
– the machine has increased survivability and absolute maintainability of equipment, thanks to the chosen layout coordinate table,
– quick installation on any non-combustible surface due to the increased stiffness of the machine and eight adjustable legs,
– easy to learn, has an intuitive management interface and after a brief training, the operator can proceed to professional plasma cutting. Through a simple and convenient system and perfect CNC plasma machine sustainable skills appear just after a few trial cuts,
– high cutting speed – up to 10 meters per minute,
– fabrication of parts with complex configurations,
– cutting of all sheet metal with the same styling.
– long-term and trouble-free operation combined with undemanding equipment maintenance during operation.
– powerful built-in smoke evacuation system divided into multiple zones for efficient use of the intake fan capacity (one area on a 1 meter coordinate table),
– intelligent zone control of the hood (only where there is a process of thermal cutting),
– bath smoke made in the form of an inverted pyramid, serving both to guide the falling parts and slag
– cut parts and slag accumulate in the catcher, where readily available with retractable hatches
– the software CNC Start-2M includes a control program of the machine Mach and a program to create the control files of the sketches, drawings, SheetCam. Both programs are simple and clear to explore each of them requires minimal time. The software includes avtoreklama products on the metal sheet, which can significantly reduce time and reduce waste when cutting,
– all settings of the machine are stored in one file, save this file on a reliable medium gives the ability to quickly restore the operation of the machine when you replace the computer system CNC
– low cost of equipment, the cost of 1 meter of cut at a metal thickness of 3 mm is 2.6 rubles.
Thermal cutting machine with two cutters designed for cutting metals in a wide range of thicknesses. Combined installation of two cutters for cutting substantially increases the versatility of the cutting machine. Applying a plasma device of small power and cutting torch in one caliper can be cut as thin metal, almost 0.5 mm and thick up to 100 mm. a Slight rise in price leads to a significant increase in the capabilities of metal cutting equipment.
Plasma and gas cutting on the machine is carried out alternately, depending on the respective technological process. Changing cutters is quick thanks to a special suspension. Learn to work on the universal machine thermal cutting is easy, having experience with plasma and gas cutting. The system automatically enters a gas cutting one switch. Ignition of the torch occurs remotely from the operator panel.
Control electronics plasma cutter and electronics gas equipment and has a total combined emergency button. For forced stop mechanisms of the machine the operator presses the “Stop” button on the remote, this stops the machine and clearing the working cutter. Gas equipment works in compliance with safety in gas cutting. In each circuit flows of the gases are set ignaravanne and check valves.
Installation of gas cutter in addition to the plasma allows cutting of metal of greater thickness up to 100 mm On agreement with the customer it is possible to manufacture reinforced desktops for metal cutting up to 200 mm.
Machines, gas cutting CNC Start-2M(Gas) is designed for thermal cutting of metal with a mixture of combustible gas and oxygen. As a cutting tool is installed efficient gas cutter with vnutrizonovyh a mixture of gases. The numerical control system extends gas machine allows cutting of parts of any complexity. The quality of the surface cut at an automated gas cutting is significantly higher than in manual.
Oxy-fuel machine unlike plasma does not require a compressor, dryer and air filters. The kit includes a gas equipment with the security system. Requires only a connection of cylinders of oxygen and fuel gas.
Gas CNC Start-2M(Gas) can be used in two modes: manual for cutting metal sheets into blanks, and automatic, for cutting parts of complex configuration. Start-2M(Gas) is made on the basis of coordinate table special design reduces to a minimum the influence of high temperature on the geometry of the table and to withstand the stresses during installation, removing heavy parts.
Oxy-fuel cutting does not require a large investment in the process of operation and has minimal maintenance requirements process. The nozzle of the cutter is virtually no wear, and as the consumables are the only cylinders with combustible gas and oxygen. Consumed gas equipment electric power does not exceed 1 KW.
As the mechanized gas cutting is provided by the movement of the cutter with a uniform and optimum speed. When cutting gas is obtained strictly vertical cut without hardening the edge of the part. The achieved accuracy depending on the configuration and size of the part, to 1 mm. Gas cutting torches are installed on the machine, are characterized by stable combustion flame without claps and reverse strokes, making it easier to work with equipment, increasing the productivity and process safety. Cutting thickness of metal is limited by the strength of the desktop and is from 2 to 100 mm On agreement with the customer it is possible to manufacture reinforced desktops for metal cutting up to 200 mm.
Work on oxy-fuel machine Start-2M (Gas) is fully automated and comes to visual monitoring of the cutting process and minor changes to the parameters by the operator of the CNC. Ignition of the torch occurs at the control unit: the operator turns on the supply of heating oxygen and fuel gas includes electriical. After successful ignition of gas-oxygen mixtures, electriical is disabled. For security, there are special ignaravanne gas valve protecting against reverse shock and flame propagation on the sleeves.
Note: the description of technology on the example of machine Start-2M.